With the robust LED work light, the entire working area in front of the TRIO can be illuminated. This makes it possible to inspect the condition of the floor or the quality of a previous sanding step before each subsequent step.
The assembly and disassembly of the LED work light is extremely quick and easy.
For running the LED work light there ist no external power supply needed! Power is supplied via an easy to disconnect plug connection on the machine. Any TRIO can be retrofitted with the work light. For safety reasons, retrofitting of the LED work light may only be carried out by us at the factory or alternatively by a qualified electrician!
• Power: 30 Watt
• Luminous flux: 3.480 lm
• Number of LEDs: 32 pieces
• Pivot range of the lighting unit: 70°
With the brushing discs specially designed for the TRIO, natural, strikingly structured surfaces can be created. After mounting the brushing set, the wooden floor can be brushed close to the wall in only one step with a very low dust level. This gives the wooden floor a rustic appearance. Depending on the type of wood and desired structure depth, the following brushing sets can be used:
Brush bristles made of abrasive nylon fibers for the structuring of softwood floors (e.g. spruce, pine, pitch pine).
Brush bristles made of brass wires for the gentle structuring of hardwood floors (e.g. oak).
Stainless steel brushes:
Aggressive brush bristles made of stainless steel wire for pronounced structuring of hardwood floors (e.g. oak). This can give the floor a particularly rustic character.
The milling disc, which is made of aluminium, can be equipped with three or six cutter holders, depending on the desired aggressiveness. Each holder carries a carbide indexable insert.
There are multiple applications for the milling discs: subfloor preparation and the removal, for example, of residual adhesive, residual felt, residual carpet backing. The TRIO milling discs can also be used on chipboards and OSB-panels.
However, they are not suitable for use on wooden floors.
Available for the TRIO.
Since October 2019, the TRIO has been delivered with a new dust bag system in which the MultiClip used until then has been replaced by a sealing fixing ring. This makes changing the dust bag even easier and faster than before. The corresponding dust bags have a larger capacity.
All TRIO Machines delivered earlier than October 2019 can be retrofitted with this system.
The cable support bracket can be attached to the chassis of the TRIO in the area of the handle. The cable support is then hooked into this. This ensures that the extension cable, which is attached to it with a rubber ring, is always held securely out of the working area of the machine.
The cable support can be turned to the right and left.
The PRCD-S serves as residual current protection device. Its use on construction sites is prescribed by the German Trade Association. It is the only mobile protective device that meets the requirements of the German Trade Association.
• detects all possible electrical faults,
• cannot be switched on in case of error,
• checks the intact protective conductor functions before switching on and during operation of the machine
• prevents the machine from restarting automatically, e.g. after the elimination of a power failure.
Our cables are reliable, safe and protect the user!
They are approved for construction sites by German VDE (Association for Electrical, Electronic & Information Technologies) and remain extremely flexible even at low temperatures. The plugs and couplings comply with protection class IP 54 (Schuko system) or IP 44 (three-phase current).
The robust cable jacket is extremely abrasion resistant as well as cut and tear proof and does not stain on wooden floor!
Damage to the coloured cable jacket can be detected immediately thanks to the white coloured inner material.
A glow lamp installed in the Schuko coupling only lights up when voltage is present. Therefore, a non-existent power supply can be detected immediately.
LÄGLER® extension cables are available in the following versions:
Cable cross-section: 3 x 1,5 mm²
Cable length: 10 m
Compatible with: LÄGLER®- Edge Sanders
Cable cross-section: 3 x 2,5 mm²
Cable length: 10 m or 20 m
Compatible with: all LÄGLER® Machines (exept machines with three-phase motor)
The following extension cable is available for three-phase motors:
Cable cross-section: 5 x 1,5 mm²
Cable length: 10 m
Compatible with: all LÄGLER® Machines with three-phase motor
The tool bag contains all the necessary tools to carry out simple maintenance work and settings on the machine by yourself. It is included in delivery of the machine.